Streamlining your entertainment experience has never been easier with the Magnavox Universal Remote for Magnavox TVs!
- List of Magnavox Universal Remote Codes for Magnavox TV MC345 and MC348
- How to program a Magnavox Universal remote with codes - Direct Code Entry Programming
- How to program a Magnavox Universal remote without codes - Auto Programming method
- How to reset a Magnavox Universal remote
- Magnavox Universal remote troubleshooting guide
- Frequently Asked Questions
If you own a Magnavox TV and want to simplify your setup, this blog post is here to help. In this comprehensive guide, we will provide you with a complete list of Magnavox Universal Remote codes (including the MC345 and MC348 models) specifically designed for Magnavox TVs.
Additionally, we will walk you through the straightforward instructions to program your remote, ensuring seamless control over your Magnavox TV using just one device.
List of Magnavox Universal Remote Codes for Magnavox TV MC345 and MC348
4 in 1 MC345 Magnavox 4 digit Universal remote codes for Magnavox TV
- 0110, 0115, 0116, 0123, 0126, 0040, 0044, 0058, 0086, 0091, 0018
8 in 1 MC348 Magnavox 4 digit Universal remote codes for Magnavox TV
- 0807, 0002, 0502, 0919, 1914, 0224, 0430, 0247, 0402, 0408, 0109, 0715
Here’s a list of codes for Magnavox universal remotes for other TV models.
How to program a Magnavox Universal remote with codes – Direct Code Entry Programming
This Magnavox remote programming method requires you to enter the appropriate universal remote codes for the device you want to program.
- Step 1: Manually turn on the device you want to control, such as your TV.
- Step 2: Refer to the Code List below and locate the four-digit code assigned to your device.
- Step 3: Press and hold the Code Search Button on the Universal Remote for approximately 2 seconds until the LED Indicator lights up.
- Step 4: After the LED indicator lights up, release the code search button.
- Step 5: Press and release the corresponding device selection button on the Universal Remote (such as the TV Button).
- Step 6: Enter the four-digit code for your device by pressing the numeric buttons.
- Step 7: The LED Indicator will turn off.
- Step 8: Point the Universal Remote towards the remote sensor on your device and test its functionality.
- Step 9: If the device responds correctly, it means you have successfully entered the correct code.
- Step 10: If the code is invalid, the Indicator will blink five times and then automatically exit.
- Step 11: In this case, you must repeat the setting procedures from Step 2 above.
How to program a magnavox universal remote with codes (direct code entry)
How to program a Magnavox Universal remote without codes – Auto Programming method
If the provided codes do not work to pair the Magnavox Universal Remote with your device, you can try the Automatic Programming method outlined below.
- Step 1: Turn on your desired device, such as your TV, using its regular power button.
- Step 2: Press and hold the “Code Search Button” on the Universal Remote for approximately 2 seconds until the LED Indicator lights up.
- Step 3: After the LED indicator lights up, release the “Code Search Button”.
- Step 4: Press and release the corresponding device selection button on the Universal Remote (such as the TV Button).
- Step 5: Point the Universal Remote towards the remote sensor of your device and press and release the “POWER Button” repeatedly to send different infrared signals of “Power off” until the LED indicator starts twinkling.
- Step 6: If it doesn’t work initially, ensure you are aiming correctly, or go back to step 2 and start all over. The Universal Remote sends a different infrared signal for “Power off” every 4 seconds.
- Step 7: Once your device has powered off, press the “ENTER Button” within 4 seconds to save the settings and exit.
- Step 8: Aim the Universal Remote at the remote sensor of your device and test its functionality by operating the device.
- Step 9: If the device responds correctly, it means you have the correct settings. If not, you can try setting it again starting from step 2 or explore alternative setting methods such as the Automatic Code search method.
How to program a magnavox universal remote without codes (auto code search)
How to reset a Magnavox Universal remote
- Remove the batteries from the universal remote.
- Wait for about one minute.
- Reinstall the batteries.
- This will reset the universal remote.
Magnavox Universal remote troubleshooting guide
- You may have installed the batteries incorrectly. Install the batteries again in accordance with the polarity marking on the battery compartment.
- The batteries are drained. Replace them with new batteries.
- The Universal Remote was incorrectly programmed. Reset the Universal Remote as instructed above.
The buttons are not working properly
- Your universal remote’s button names may differ from those on the original manufacturer’s controller.
The buttons don’t perform the expected functions
- Some of the buttons may not operate your device in the same way as your original remote.
Frequently Asked Questions
Can I use a Magnavox Universal remote with any TV?
Yes, the Magnavox Universal Remote is compatible with most TV brands. However, it’s important to ensure that you have the correct codes for your specific TV model.
How do I find the correct code for my device?
You can find the code for your device in the instruction manual that comes with the Magnavox Universal remote or by browsing the various codes we provided at this link.
Can I program the Magnavox Universal Remote to control multiple devices of the same type?
Yes, you can program the remote to control multiple devices of the same type, such as multiple TVs or DVD players. Simply follow the programming steps for each device.
What should I do if the remote doesn’t work after programming?
If the remote doesn’t work as expected, try reprogramming it using the correct codes for your devices.
Also, ensure that the batteries are properly inserted and have sufficient charge. You may refer to the troubleshooting guide that we have provided above in this article.
Can I control devices other than TVs and DVD players with the Magnavox Universal remote?
Yes, the Magnavox Universal Remote can control various devices, including audio systems, streaming devices, and gaming consoles. You need to program the remote with the appropriate codes for each device.
This blog post has provided a comprehensive guide for using the Magnavox Universal Remote with Magnavox TVs.
It includes a complete list of Magnavox Universal Remote codes for the MC345 and MC348 models, specific to Magnavox TVs.
The post also offers step-by-step instructions for programming the remote, covering both direct code entry programming and auto programming methods. In case of any issues, a reset procedure and troubleshooting guide are provided.
The post concludes with frequently asked questions, addressing common concerns, and clarifying the compatibility of the Magnavox Universal Remote with various devices.
Overall, this guide serves as a valuable resource for simplifying the control of Magnavox TVs using the Magnavox Universal Remote.
Disclaimer: As An Amazon Affiliate, We Earn From Qualifying Purchases